Direct Characterization of Buried Interfaces in 2D/3D Heterostructures Enabled by GeO2 Release Layer.

Inconsistent interface control in devices based on two-dimensional materials (2DMs) has limited technological maturation. Astounding variability of 2D/three-dimensional (2D/3D) interface properties has been reported, which has been exacerbated by the lack of direct investigations of buried interfaces commonly found in devices. Herein, we demonstrate a new process that enables the assembly and isolation of device-relevant heterostructures for buried interface characterization. This is achieved by implementing a water-soluble substrate (GeO2), which enables deposition of many materials onto the 2DM and subsequent heterostructure release by dissolving the GeO2 substrate. Here, we utilize this novel approach to compare how the chemistry, doping, and strain in monolayer MoS2 heterostructures fabricated by direct deposition vary from those fabricated by transfer techniques to show how interface properties differ with the heterostructure fabrication method. Direct deposition of thick Ni and Ti films is found to react with the monolayer MoS2. These interface reactions convert 50% of MoS2 into intermetallic species, which greatly exceeds the 10% conversion reported previously and 0% observed in transfer-fabricated heterostructures. We also measure notable differences in MoS2 carrier concentration depending on the heterostructure fabrication method. Direct deposition of thick Au, Ni, and Al2O3 films onto MoS2 increases the hole concentration by >1012 cm-2 compared to heterostructures fabricated by transferring MoS2 onto these materials. Thus, we demonstrate a universal method to fabricate 2D/3D heterostructures and expose buried interfaces for direct characterization.

Bio-inspired incorporation of phenylalanine enhances ionic selectivity in layer-by-layer deposited polyelectrolyte films.

The addition of a common amino acid, phenylalanine, to a Layer-by-Layer (LbL) deposited polyelectrolyte (PE) film on a nanoporous membrane can increase its ionic selectivity over a PE film without the added amino acid. The addition of phenylalanine is inspired by detailed knowledge of the structure of the channelrhodopsins family of protein ion channels, where phenylalanine plays an instrumental role in facilitating sodium ion transport. The normally deposited and crosslinked PE films increase the cationic selectivity of a support membrane in a controllable manner where higher selectivity is achieved with thicker PE coatings, which in turn also increases the ionic resistance of the membrane. The increased ionic selectivity is desired while the increased resistance is not. We show that through incorporation of phenylalanine during the LbL deposition process, in solutions of NaCl with concentrations ranging from 0.1 to 100 mM, the ionic selectivity can be increased independently of the membrane resistance. Specifically, the addition is shown to increase the cationic transference of the PE films from 81.4% to 86.4%, an increase on par with PE films that are nearly triple the thickness while exhibiting much lower resistance compared to the thicker coatings, where the phenylalanine incorporated PE films display an area specific resistance of 1.81 Ω cm2 in 100 mM NaCl while much thicker PE membranes show a higher resistance of 2.75 Ω cm2 in the same 100 mM NaCl solution.

How Hydrogen and Oxygen Vapor Affect the Tribochemistry of Silicon- and Oxygen-Containing Hydrogenated Amorphous Carbon under Low-Friction Conditions: A Study Combining X-ray Absorption Spectromicroscopy and Data Science Methods.

The incorporation of silicon and oxygen into hydrogenated amorphous carbon (a-C:H) is an effective approach to decrease the dependence of the tribological properties of a-C:H on the environment. Here, we evaluate the effect of hydrogen and oxygen partial pressures in vacuum on the tribological response of steel pins sliding against films consisting of silicon- and oxygen-containing a-C:H (a-C:H:Si:O). Experiments are conducted in the low-friction/low-wear regime, where sufficient gas pressure prevents steel from adhering to the a-C:H:Si:O, with the velocity accommodation mode being interfacial sliding between the tribotrack formed in the a-C:H:Si:O film and the carbonaceous tribofilm that is formed on the countersurface. The experiments indicated a decrease (increase) in friction and wear with the hydrogen (oxygen) pressure (hydrogen pressures between 50 and 2000 mbar; oxygen pressures between 10 and 1000 mbar). Characterization by X-ray photoelectron and absorption spectroscopies indicated the occurrence of tribologically induced rehybridization of carbon-carbon bonds from sp3 to sp2. This mechanically induced structural transformation coincided with the dissociative surface reaction between hydrogen (oxygen) gas molecules and sp2 carbon-carbon bonds that are highly strained, which results in the formation of carbon-hydrogen groups (carbonyl or ether groups together with silicon atoms having higher oxidation states). On the basis of variations of the fraction of these surface functional groups with gas pressure, a phenomenological model is proposed for the gas pressure dependence of friction for steel when sliding on a-C:H:Si:O films: while the decrease in friction with hydrogen pressure is induced by an increase in the percentage of carbon-hydrogen groups, the increase in friction with oxygen pressure is caused by a progressive increase in the relative fraction of silicon atoms having higher oxidation states and an increase in surface oxygen concentration.

Tribochemical polymerization of adsorbed n-pentanol on SiO2 during rubbing: when does it occur and is it responsible for effective vapor phase lubrication?

The origin and role of tribochemical reaction products formed while sliding silicon oxide surfaces in the presence of adsorbed alcohol molecules in equilibrium with the vapor phase were studied. Wear and friction coefficient studies with varying contact loads and n-pentanol vapor environments were used to determine under what operating conditions the tribochemical reaction species was produced. Imaging time-of-flight secondary ion mass spectrometry and microinfrared spectroscopy found that hydrocarbon species with a molecular weight higher than the starting vapor molecules are produced when there is wear of the SiO(2) surface. When the n-pentanol vapor lubrication is effective and the silicon oxide surface does not wear, then the tribochemical polymerization products are negligible. These results imply that the tribochemical polymerization is associated with the substrate wear process occurring due to insufficient adsorbate supply or high mechanical load. The tribochemical reactions do not seem to be the primary lubrication mechanism for vapor phase lubrication of SiO(2) surfaces with alcohol, although they may lubricate the substrate momentarily upon failure of the alcohol vapor delivery to the sliding contact.

Forensic analysis of bioagents by X-ray and TOF-SIMS hyperspectral imaging.

Hyperspectral imaging combined with multivariate statistics is an approach to microanalysis that makes the maximum use of the large amount of data potentially collected in forensics analysis. This study examines the efficacy of using hyperspectral imaging-enabled microscopies to identify chemical signatures in simulated bioagent materials. This approach allowed for the ready discrimination between all samples in the test. In particular, the hyperspectral imaging approach allowed for the identification of particles with trace elements that would have been missed with a more traditional approach to forensic microanalysis. The importance of combining signals from multiple length scales and analytical sensitivities is discussed.

Macro- to nanoscale wear prevention via molecular adsorption.

As the size of mechanical systems shrinks from macro- to nanoscales, surface phenomena such as adhesion, friction, and wear become increasingly significant. This paper demonstrates the use of alcohol adsorption as a means of continuously replenishing the lubricating layer on the working device surfaces and elucidates the tribochemical reaction products formed in the sliding contact region. Friction and wear of native silicon oxide were studied over a wide range of length scales from macro- to nanoscales using a ball-on-flat tribometer (millimeter scale), sidewall microelectromechanical system (MEMS) tribometer (micrometer scale), and atomic force microscopy (nanometer scale). In all cases, the alcohol vapor adsorption successfully lubricated and prevented wear. Imaging time-of-flight secondary ion mass spectrometry analysis of the sliding contact region revealed that high molecular weight oligomeric species were formed via tribochemical reactions of the adsorbed linear alcohol molecules. These tribochemical products seemed to enhance the lubrication and wear prevention. In the case of sidewall MEMS tests, the lifetime of the MEMS device was radically increased via vapor-phase lubrication with alcohol.